Design of PLC and VSD Trainers for Starting Electric Motors in Electrical Machine Control Courses

Authors

  • M. Fauzi Albillah UIN AR-RANIRY
  • Malahayati UIN Ar-Raniry, Banda Aceh
  • Muhammad Ikhsan Ar-Raniry State Islamic University Banda Aceh

Keywords:

Planning, Starting Electric Motor, Trainer, PLC, VSD

Abstract

Starting an electric motor using a PLC and VSD is one of the materials in the Electrical Machine Control course which requires a medium to facilitate students during practicum. This practical trainer was developed as an aid to assist lecturers in elucidating the material on starting electric motors using PLC and VSD. The types of PLC and VSD trainers in this research used Zelio PLC type SR2 B201FU and VSD Altivar 312. This research used research & development methods in designing the PLC and VSD trainers. The instrument of this research was a media expert and material expert validation sheet to examine the feasibility of the trainer to be applied in the Electrical Machine Control Course. The results of media experts' and material experts' validation prove that Using PLC and VSD trainers for starting electric motors in the Electrical Machine Control Course is very feasible in terms of media and material. Where the percentage of scores obtained from media expert 1 was 96%, media expert 2 was 92%, material expert 1 was 80%, and material expert 2 was 94%. So, the feasibility of this trainer is included in the very feasible category to be applied in the Electrical Machine Control Course.

References

Abdelsalam A. Ahmed, dkk. “Improving energy efficiency and economics of motor-pump-system using electric variable-speed drives for automatic transition of working points”. Computers & Electrical Engineering, Vol. 97, 2022.
Anas M, “Alat Peraga & Media Pembelajaran, Jakarta, pustaka education, Andri Ferdiansyah, dkk. Rancang Bangun Sistem Pencahayaan Otomatis Berbasis Pemrograman Ladder PLC (Programmable Logic Controller) Zelio”. Teknologi Elektro, Vol. 15, No. 2, 2016.
Atiq Iqbal, dkk. Electrical Machine Fundamentals with Numerical Simulation Using MATLAB / SIMULINK. Britania Raya: Wiley. 2021.
Bambang Suprianto.,“Rancang Bangun Modul Forward Reverse Motor 3 Fasa Bserta Pengereman Dinamik Menggunakan PLC ZELIO SR B121FU” , jurnal Teknik Elektro. Vol. 11, No. 1, 2022.
Eko Rohmatul Hidayat dan Bambang Supriyanto. “Validasi Pengembangan Media Pembelajaran Trainer Mikrokontroler Model Traffic Light Pada Mata Pelajaran Mikroprosesor Dan Mikrokontroler”. Surabaya: Jurnal Pendidikan Teknik Elektro. Vol.10. No.1. 2021.
Hariyanto., “Pengembangan Media Pembelajaran Trainer Kit Pengendali Motor 3 Phase Pada Mata Pelajaran Instalasi Motor Listrik Di SMKN 4 Kota Serang” Vol 5, No.1. 2020.
Indyah hartami santi., “Analisa Perancangan Sistem”. Pt.Nasya Expanding Management: jawa tengah. 978-623-7566-83-0, 2020.
Isaac Chairez dan Vadim Utkin. “Direct Current Motor Position Control by a Sliding Mode Controlled Dual Three-Phase AC-DC Power Converter”. IFAC-PapersOnLine, Vol. 55, 2022.
Jeffery Hampson, Steven Hanssen. Electrotechnology Practice. Australia: Cengage Learning Australia. 2019.
Komaruddin, dkk. Perancangan Trainer Motor Induksi AC 3PH Berbasis Program Logic Controller. Sigma Teknika, Vol 4, No 2. 2021.
Lijuan Xu, dkk. “PLC-SEIFF: A programmable logic controller security incident forensics framework based on automatic construction of security constraints”. Computers & Security, Vol. 92, 2020.
Mirza Sultan Farza, dkk. “Perancangan Trainer Kendali Motor Listrik Berbasis PLC Pada Mata Kuliah Praktikum Pengendalian Mesin Listrik”. Skripsi, UIN Ar-Raniry Banda Aceh. 2022.
Mohammad Reza Semsar, dkk. “A novel topology of drive & thermal model for variable speed pump-storage power plant”. Journal of Energy Storage, Vol. 73, 2023.
Mohammad Yudi Irawan, “Perancangan Kendali Motor Listrik Berbasis Smart Relay (Zelio)”. Jurnal Teknik Elektro Dan Komputer Triac Vol. 8, No. 2. 2021.
Nur Indrihastuti, dkk, “Perancangan Kendali 2 Kontaktor Bekerja Berurutan Secara Otomatis Berbasis PLC CPM1A 40CDR_A’’. Jurnal cahaya bagaskara Vol. 6. No. 2, 2021.
Perez-Loya, J. J., dkk. “Demonstration of Synchronous Motor Start by Rotor Polarity Inversion”. IEEE Transactions on Industrial Electronics, Vol. 65, 2018.
Prakoso, Aprileo Nanda Dwi Pengembangan Media Pembelajaran Refrigerator Untuk Mata Pelajaran Sistem Dan Instalasi Refrigerasi Smk Negeri 1 Denpasar. Undergraduate Thesis. Universitas Pendidikan Ganesha. h.1,2,3. 2021.
Rima Asmar Awad, dkk. “Towards generic memory forensic framework for programmable logic controllers”. Forensic Science International: Digital Investigation, Vol. 44, 2023.
Sandhy Nuari, dkk. Analisis Starting Motor Induksi Tiga Phasa Menggunakan Programmable Logic Controller (PLC). SainETIn (Jurnal Sain, Energi, Teknologi & Industri), Vol. 2, No. 2. 2018.
Santeri Pöyhönen, dkk. “Variable-speed-drive-based method for the cost optimization of air filter replacement timing”. Energy and Buildings, Vol. 240, 2021.
Setiyadi, Surawan. Pembuatan Aplikasi Pembelajaran Praktikum PLC Secara Daring Menggunakan PLC Omron CP1E untuk Menghadapi Pandemi Covid-19. Technologic, Vol. 11, No. 2. 2020.
Stephen L. Herman. Electrical Wiring Industrial. Amerika Serikat: Cengage Learning. 2020.
Sugiyono (2022). “Metode Penelitian dan Pengembangan (Research and Development).” UPT Perpustakaan Universitas Muhammadiyah Metro.
Syahrul Mustafa dkk., “Rancang Bangun Media Pembelajaran Trainer PLC” Vol. 3, No. 2, Bulan Agustus Tahun 2022 POLITEKNIK BOSOWA.
Taufik, D. M., & De Wibowo, A. “Sistem Penetasan Telur Berbasis PLC”. Jurnal Rekayasa Teknologi Nusa Putra, Vol.7 No.1. 2020.
Togar Timoteus Gultom. Programmable Logic Control. Medan: Jurnal Ilmiah Maksitek, Vol. 5, No. 4. 2020.
Tri Isra Janwardi. Rancang Alat Rewinding Motor Listrik dengan Kendali PLC. Jurnal Elektronika, Listrik dan Teknologi Informasi Terapan Vol. 1, No. 2. 2019.
Wilda Susanti. Pembelajaran Aktif, Kreatif, Dan Mandiri Pada Mata Kuliah Algoritma Dan Pemrograman. Yogyakarta: samudra biru, hal:91. 2021.
Yazan Alsmadi, dkk. “Direct Sliding Mode Control of a Three-Phase AC/DC Power Converter for the Velocity Regulation of a DC Motor”. IFAC- PapersOnLine, Vol. 53, 2020.
Yudi Mulyanto, Dkk. “Rancang Bangun Sistem Informasi Penjualan Pada Toko Omg Berbasis Web Kecematan Empang Kabupaten Sumbawa” Jurnal JINTEKS. Vol. 2 No. 1. Hal: 70. Tahun 2020.

Downloads

Published

2024-07-26

Issue

Section

Articles